Crown Micro-Tech MT-1000 User Manual

Browse online or download User Manual for Audio amplifiers Crown Micro-Tech MT-1000. MT-Series Spec. Sheet

  • Download
  • Add to my manuals
  • Print
  • Page
    / 2
  • Table of contents
  • BOOKMARKS
  • Rated. / 5. Based on customer reviews
Page view 0
MT-600
MICRO-TECH SERIES
T
he Crown
®
Micro-Tech
®
600, 1200 and
2400 are the original industry standards
for touring amplifiers. Micro-Tech ampli-
fiers are known around the world as the
benchmark for high-density, ultra-pure power
in a compact package. In addition, each
model gives you Crown’s legendary ODEP
®
protection to keep the show going long after
other amplifiers would fail.
Micro-Tech
amplifiers use proven technology
and a miniaturized design to deliver terrific
value for their size, weight and price. Crown’s
patented ODEP protection circuitry and
Grounded Bridge
output stages combine to
provide performance and reliability that
surpass traditional designs. Micro-Tech
amplifiers also have an independent high-
voltage power supply for each channel. This
approach results in extremely low crosstalk
and makes it possible to use each channel as
a separate amplifier.
Plus, your investment in a Micro-Tech ampli-
fier is backed by Crown’s unequaled Three-
Year, No-Fault, Fully Transferable Warranty
that covers everything.
For more details about the Crown Micro-Tech
Series, contact the Crown Technical Support
Group at 800-342-6939 or 574-294-8200.
Also, visit the Crown Audio website at
www.crownaudio.com.
Specifications
The following applies to 120 VAC, 60 Hz units in Stereo mode
with both channels driven into 8 ohm loads and an input
sensitivity of 26 dB unless otherwise specified. Specifications
for units supplied outside the USA may vary slightly at
different AC voltages and frequencies.
Power
Output Power: See power charts below.
Load Impedance: Safe with all types of loads.
Rated for 2 to 16 ohms in Stereo mode, 4 to
16 ohms in Bridge-Mono mode, and 1 to 4
ohms in Parallel-Mono mode.
Voltage Gain (at maximum level setting):
MT-600: 20:1 ±6% or 26 dB ±0.5 dB at 26
dB gain setting. 55:1 ±6% or 35 dB ±0.5 dB
at 0.775 volt sensitivity; 31:1 ±6% or 30 dB
±0.5 dB at 1.4 volt sensitivity.
MT-1200: 20:1 ±6% or 26 dB ±0.5 dB at 26
dB gain setting. 64:1 ±6% or 36 dB ±0.5 dB
at 0.775 volt sensitivity; 34:1 ±6% or 31 dB
±0.5 dB at 1.4 volt sensitivity.
MT-2400: 20:1 ±6% or 26 dB ±0.5 dB at 26
dB gain setting. 83:1 ±6% or 38 dB ±0.5 dB
at 0.775 volt sensitivity; 46:1 ±6% or 33 dB
±0.5 dB at 1.4 volt sensitivity.
Required AC Mains: 100, 120, 220 and
240VAC (±10%), 50 and 60 Hz units are
available.
AC Line Current:
AC mains current, frequency and voltage
requirements are provided on the unit’s
back panel.
At Idle: All amps draw no more than
90 watts.
AC Line Connector: All units are shipped with
an appropriate plug and cord for the required
AC voltage.
Performance
Frequency Response: ±0.1 dB from 20 Hz to
20 kHz at 1 watt.
Phase Response: ±10 degrees from 20 Hz to
20 kHz at 1 watt.
Signal to Noise Ratio:
A-Weighted:
Better than 105 dB below full bandwidth
power.
20 Hz to 20 kHz:
Better than 100 dB below full bandwidth
power.
Total Harmonic Distortion (THD): Less than
0.5% at full bandwidth power from 20 Hz to 1
kHz increasing linearly to 0.1% at 20 kHz.
Intermodulation Distortion (IMD): (60 Hz and
7 kHz at 4:1) Less than 0.05% from 163
milliwatts to full bandwidth power.
Damping Factor: Better than 1,000 from 10
Hz to 400 Hz.
Common Mode Rejection (CMR): At rated full
bandwidth power, better than 70 dB from 20
Hz to 1 kHz falling linearly to better than 50 dB
at 20 kHz.
DC Output Offset (Shorted Input): ±10 mV.
Features
Crown’s Grounded Bridge™ design
delivers large voltage swings without
using easily stressed output-transistor
configurations like conventional amplifi-
ers. The results are lower distortion and
superior reliability.
Patented ODEP
®
(Output Device Emula-
tion Protection) circuitry compensates for
overheating and overload to keep the
amplifier working when others would fail.
High damping factor provides superior
motion control over low-frequency drivers
for clean, accurate low end.
Full protection against shorted outputs,
open circuits, DC, mismatched loads,
general overheating, high-frequency
overloads and internal faults.
1/4-inch and balanced XLR input connec-
tors.
Ground lift switch to isolate chassis and
phone jack audio grounds.
Internal three-position input sensitivity
switch provides settings of 0.775 and 1.4
volts for standard 1 kHz power, and 26 dB
voltage gain.
The best Three-Year, No-Fault, Fully
Transferable Warranty in the business.
MT-1200
MT-2400
8 ohm Stereo (per channel)
1 kHz
Power
225W
325W
400W
655W
750W
4 ohm Bridge-Mono
8 ohm Bridge-Mono
2 ohm Stereo (per channel)
4 ohm Stereo (per channel)
MT 600
*1 kHz Power: refers to maximum average power in watts
at 1 kHz with 0.1% THD.
*
8 ohm Stereo (per channel)
1 kHz
Power
520W
800W
1,050W
1,585W
2,070W
4 ohm Bridge-Mono
8 ohm Bridge-Mono
2 ohm Stereo (per channel)
4 ohm Stereo (per channel)
MT 2400
*1 kHz Power: refers to maximum average power in watts
at 1 kHz with 0.1% THD.
*
8-ohm Stereo (per channel)
1 kHz
Power
310W
480W
675W
970W
1,300W
4-ohm Bridge-Mono
8-ohm Bridge-Mono
2-ohm Stereo (per channel)
4-ohm Stereo (per channel)
MT 1200
*1 kHz Power: refers to maximum average power in watts
at 1 kHz with 0.1% THD.
*
Page view 0
1 2

Summary of Contents

Page 1 - MICRO-TECH SERIES

MT-600MICRO-TECH SERIESThe Crown® Micro-Tech® 600, 1200 and2400 are the original industry standardsfor touring amplifiers. Micro-Tech ampli-fiers are

Page 2 - (Shorted input) ±10 milli

Crown InternationalP.O. Box 1000Elkhart, IN 46515-1000TEL: 574-294-8200FAX: 574-294-8FAXwww.crownaudio.comSpecifications subject to change without pri

Comments to this Manuals

No comments