Modified for theWorld Wide WebTrademark Notice:AMB-5,™ SMX-6 ,™ MPX-6,™ Distributed Intelligence,™ and Algo™ are trademarks and Crown,®Amcron,® IQ Sys
Page 10IQ Mixer/Multiplexer Hardware InstallationRev. 03 Hardware InstallationThe installation of an IQ mixer/multiplexer consistsof two major parts:
Page 11IQ Mixer/Multiplexer Hardware InstallationRev. 0It is also possible to use RS232 to communicatewith a Macintosh computer. Here’s how to wire t
Page 12IQ Mixer/Multiplexer Hardware InstallationRev. 012345678RS232RS422123456IQ ADDRESSBAUD RATE& PARITYCOMSTANDARD123456ODDEVEN192009600480012
Page 13IQ Mixer/Multiplexer Hardware InstallationRev. 0Crown Bus can have the same address. Suppose,for example, an IQ System has two Crown Busloops
Page 14IQ Mixer/Multiplexer Hardware InstallationRev. 0Figure 3.9 Crown Bus Wiring ÷Loopsš from Output to Input of Each IQ ComponentFig. 3.7 Crown
Page 15IQ Mixer/Multiplexer Hardware InstallationRev. 0added to the audio lines. Use only the signallines which normally connect to pins 2 and 3 ofth
Page 16IQ Mixer/Multiplexer Hardware InstallationRev. 00.775 volts). Select the center position (L) for linelevel signals up to +32 dBu. Slide it to
Page 17IQ Mixer/Multiplexer Hardware InstallationRev. 0system). Because the bus outputs are controlled bythe IQ System, they can be kept off until th
Page 18IQ Mixer/Multiplexer Hardware InstallationRev. 03.3.4 Stack InputsThe stack in jacks (Figure 3.15) enable the audioinputs to be increased by
Page 19IQ Mixer/Multiplexer Hardware InstallationRev. 0Fig. 3.22 A 12x8 Mixer Using 8 Mixer/MultiplexersBy using several units and a combination of
NORTH AMERICASUMMARY OF WARRANTYCROWN, a division of Crown International, Inc., 1718 West Mishawaka Road,Elkhart, Indiana 46517-4095 U.S.A. warrants t
Page 20IQ Mixer/Multiplexer Hardware InstallationRev. 04 OptionsThere are two optional uses for mixer serial ports.The first is direct RS232/RS422 co
Page 21IQ Mixer/Multiplexer Hardware InstallationRev. 0237910237910237910PinPinPin(Optional) (Optional)(Optional)Pin 2 Serial In (–)Pin 3 Serial Out
Page 22IQ Mixer/Multiplexer Hardware InstallationRev. 05.2.2 Crown Factory ServiceTo obtain factory service, fill out the Service Infor-mation Card i
Page 23IQ Mixer/Multiplexer Hardware InstallationRev. 06 Technical InformationThe IQ System was developed to provide a way toboth monitor and control
Page 24IQ Mixer/Multiplexer Hardware InstallationRev. 06.2.3 D/A ConverterTo set channel gain levels, a digital-to-analog con-verter continuously co
Page 25IQ Mixer/Multiplexer Hardware InstallationRev. 0Fig. 6.1 General IQ Mixer Block DiagramINPUT 1PRE-AMPBALANCEDBUCHANANCONNECTORGAIN POT(-12 to
Page 26IQ Mixer/Multiplexer Hardware InstallationRev. 07 Specifications7.1 GeneralProtection: Audio outputs can be shorted indefi-nitely without cau
Page 27IQ Mixer/Multiplexer Hardware InstallationRev. 0Appendix AThis Appendix contains look-up tables for everyvalid IQ address. The valid address a
Page 28IQ Mixer/Multiplexer Hardware InstallationRev. 0OFFONOFFONOFFONOFFONOFFONOFFONOFFONOFFONOFFONOFFONOFFONOFFONOFFONOFFONOFFONOFFONOFFONOFFONOFFO
The information furnished in this manual does not include all of the details of design, production, orvariations of the equipment. Nor does it cover e
Page 4IQ Mixer/Multiplexer Hardware InstallationRev. 0CONTENTS1 Welcome ...71.1 O
Page 5IQ Mixer/Multiplexer Hardware InstallationRev. 0ILLUSTRATIONS1.1 Three Mixer / Multiplexer Models ... 62.1 Front and R
Page 6IQ Mixer/Multiplexer Hardware InstallationRev. 0Fig. 1.1 Three Mixer / Multiplexer ModelsENABLEDSPIENABLEDSPI
Page 7IQ Mixer/Multiplexer Hardware InstallationRev. 01 WelcomeThank you for purchasing a Crown IQ mixer/multi-plexer. IQ mixer/multiplexers are inte
Page 8IQ Mixer/Multiplexer Hardware InstallationRev. 0(Rear View)(Front View)2 FacilitiesAUX ConnectorA 3-pin male mini-XLR connector is used for rem
Page 9IQ Mixer/Multiplexer Hardware InstallationRev. 0optional shield for the Crown Bus cable. Only theshield of the input cable should be connected.
Comments to this Manuals