Crown S series Instruction Manual

Operation ManualS-2Obtaining Other Language Versions: To obtain information in another language about the use of this product, please contact your loc

Operation ManualS-Series Power Amplifierspage 102 SetupFigure 2.11 Typical System Wiring, Bridge-Mono Mode 2.6.3 Bridge-Mono ModeMake sure the ampl

page 11S-Series Power AmplifiersOperation Manual2.8 Connect to AC Mains Connect your amplifier to the AC mains power source (power outlet) with the su

Operation ManualS-Series Power Amplifierspage 123.1 PrecautionsYour amplifier is protected from internal and exter-nal faults, but you should still ta

page 13S-Series Power AmplifiersOperation ManualFigure 3.1 Controls, Indicators & Connectors3 Operation3.2 Controls, Indicators and Connectors

Operation ManualS-Series Power Amplifierspage 143 Operation3.4 Back Panel Controls andConnectorsInput Sensitivity SwitchThis two-position Input Sensit

page 15S-Series Power AmplifiersOperation ManualNOTE: For detailed information about these Crown amplifier features, please consult the Crown Amplifie

Operation ManualS-Series Power Amplifierspage 16SST-SBSC-3632TThis is a custom three-channel crossover net-work with CD-horn equalization and summed l

page 17S-Series Power AmplifiersOperation Manual4.2.2 Fault MonitoringThe Fault (RJ-11) jack, which looks like a telephone jack, is located on the bac

Operation ManualS-Series Power Amplifierspage 18To use, simply pull off the control knobs from the front of the amp, and slip the hole plugs into plac

page 19S-Series Power AmplifiersOperation ManualFor the sake of simplicity, only channel one of the amplifier is described. Signal is presented to the

Operation ManualS-Series Power Amplifierspage 21) Read these instructions.2) Keep these instructions.3) Heed all warnings.4) Follow all instructions.5

Operation ManualS-Series Power Amplifierspage 205 Principles of OperationFigure 5.1S-SeriesAmplifier Block Diagram (Shown with Standard Input Module)T

page 21S-Series Power AmplifiersOperation ManualCONDITION: Power indicator is off.POSSIBLE REASON• The amplifier has lost AC power.• The amplifier’s P

Operation ManualS-Series Power Amplifierspage 227 SpecificationsMinimum Guaranteed Power S-2 S-3120 VAC, 60 Hz Units, Stereo mode, per channel, both c

page 23S-Series Power AmplifiersOperation ManualCrown amplifiers are quality units that rarely require ser-vicing. Before returning your unit for serv

Operation ManualS-Series Power Amplifierspage 24YEAR39 WarrantyWORLDWIDE EXCEPT USA & CANADASUMMARY OF WARRANTYCrown International, 1718 West Mish

page 25S-Series Power AmplifiersOperation ManualThis page intentionally left blank.

Operation ManualS-Series Power Amplifierspage 26This page intentionally left blank.

page 27S-Series Power AmplifiersOperation ManualPLEASE PRINT CLEARLYSRA #: __________________(If sending product to Crown factory service.)

page 3S-Series Power AmplifiersOperation ManualDECLARATION of CONFORMITYCrown International, Inc.Sue [email protected]

Operation ManualS-Series Power Amplifierspage 4Important Safety Instructions ...2Declaration of Co

page 5S-Series Power AmplifiersOperation Manual1 WelcomeCrown® S-Series amplifiers provide profes-sional audio amplification for a wide range of appli

Operation ManualS-Series Power Amplifierspage 62.1 Unpack Your AmplifierPlease unpack and inspect your amplifier for any damage that may have occurred

page 7S-Series Power AmplifiersOperation Manual2.4 Choose Input Wire and ConnectorsYou have three choices of input connectors:1/4-inch (6.35-mm) phone

Operation ManualS-Series Power Amplifierspage 82.5 Choose Output Wire and Con-nectorsCrown recommends using pre-built or profes-sionally wired, high-q

page 9S-Series Power AmplifiersOperation Manual2.6 Wire Your System2.6.1 Stereo ModeMake sure the amplifier is turned off and the level controls are